realizzazione siti internet ed e-commerce mugello

Risultati da 1 a 3 di 3
Like Tree2Likes
  • 2 Post By Pa0l0ne

Discussione: [GUIDE e TUTORIAL] Dreamcast ed Alimentatore ATX...Why not?

  1. #1
    Shamalaya! L'avatar di Pa0l0ne
    Data Registrazione
    Sep 2014
    Località
    Perugia
    Messaggi
    680
    Post Thanks / Like

    [GUIDE e TUTORIAL] Dreamcast ed Alimentatore ATX...Why not?

    Come si evince anche dalla serigrafia...




    E allora...perchè no?



    Soprattuto perchè utilizzando questo:



    Si misurano ~14,24v anzichè i ~13v del lettore GDROM standard.

    E' consigliabile quindi in presenza di lettore GDROM scollegato, dare un certo carico alla linea dei 12v (ad esempio tramite una ventola aggiuntiva) in modo da far scendere il voltaggio al suo standard ~13. In alternativa collegando un'alimentazione ATX si potrebbe pensare di eliminare completamente la linea dei 12v se non si hanno particolari periferiche od addons che ne fanno uso (sarebbe da testare in presenza di più pad con visual memory)

    Con l'USB GDROM Emulator sono questi gli amperaggi misurati (Courtesy of Rocky5 del forum Assemblergames) nel caso si voglia acquistare un PICO PSU (Specialmente perchè per via dell'utilizzo dell'USB i 5v verranno sollecitati maggiormente rispetto all'utilizzo stock, a maggior ragione se viene utilizzato un harddisk esterno anzichè la classica pennetta):

    2.5Ah @ 3,3v
    2Ah @ 5v
    0Ah @12v (utilizzando un solo PAD e nessun'altra periferica esterna)

    Dunque assieme all'eventuale PICO PSU è importante anche dotarsi di alimentatore esterno che eroghi almeno 5Ah

    Ecco una foto del collegamento fatto dall'utente Rocky5 del forum Assemblergames:



    Interessante? No! Nerd!
    Ultima modifica di Pa0l0ne; 15-10-2014 alle 23:07
    sparco1990 and HOPEdieFAST like this.

  2. Likes Sk8er000 Ha dato un "mi piace" per questo post
    Thanks Sk8er000 Ha ringraziato per questo post
  3. #2
    Senior Member
    Data Registrazione
    Sep 2014
    Messaggi
    111
    Post Thanks / Like
    mi piaceeeee

  4. #3
    Shamalaya! L'avatar di Pa0l0ne
    Data Registrazione
    Sep 2014
    Località
    Perugia
    Messaggi
    680
    Post Thanks / Like
    Anche con l'uso del GDEMU (l'ode concorrente di quello di Mnemo) la situazione voltaggi non cambia, ecco.uno stralcio preso proprio dal blog di GDEMU:

    One other point of interest, PSU voltages:

    GD-ROM drive (no disc): 3.296V / 5.030V / 13.28V
    GDEMU: 3.305V / 5.042V / 14.26V
    Even without a disc inserted the original drive pulls some current from 12V line. GDEMU doesn’t (and uses much less power in general) so it’s possible the PSU is running in a bit less efficient way now.

    Keep in mind this a 230V PSU, the 110V one might behave differently. I’m going to test that as well in a day or two. Still, the capacitors in the PSU are 105°C rated so 70 rather than 58 degrees is not going to suddenly damage them. If this thing was properly designed it should handle even less favourable conditions than that. After all SEGA guys did put the fan on the opposite side so overheating the PSU was not a major concern for them.

Segnalibri

Permessi di Scrittura

  • Tu non puoi inviare nuove discussioni
  • Tu non puoi inviare risposte
  • Tu non puoi inviare allegati
  • Tu non puoi modificare i tuoi messaggi
  •